Sikafloor®-Comfort Regupol 6015H
发布时间：2023/05/11
Product Data Sheet
Edition 03/03/2012EN
Sikafloor®-Comfort Regupol 6015H
1
1/3
Sikafloor®-Comfort Regupol 6015H
Sikafloor® -Comfort Regupol 6015H
Rubber shockpad part of the Sika® -ComfortFloor® Pro
Product
Description
Sikafloor® -Comfort Regupol 6015H is a prefabricated rubber shockpad produced by
bonding rubber crump with a polyurethane compound.
Uses
Is a durable high quality rubber shockpad
Particularly suitable for hospitals, schools, sales premises, showrooms,
entrance halls, lobbies, open-plan offices, museums
For interior use only
Characteristics /
Advantages
Permanently flexible
Shock and sound absorption
High hardness
High impact resistance
Easy to apply
Product Data
Form
Colour
Black
Thickness Width Length Area Net weight Gross weight
4 mm 1.5 m 45 m 67.5 m² 2.7 kg/m² 187 kg/roll
Packaging
Roll diameter ≈ 50 cm
Storage
Storage Conditions
Store the rolls horizontally in an environment where protection against damage and
free flowing water is guaranteed.
System
Information
System Structure Sika® -ComfortFloor® Pro:
Adhesive: 1 x Sikafloor® -Comfort Adhesive
Rubber Shockpad: 1 x Sikafloor® -Comfort Regupol 6015 H
Porefiller: 1 x Sikafloor® -Comfort Porefiller
Wearing course: 1 x Sikafloor® -330
Seal coat (mandatory): 1-2 x Sikafloor® -305 W
Construction2
2/3
Sikafloor®-Comfort Regupol 6015H
Application Details
Substrate Quality
Concrete substrates must be sound and of sufficient compressive strength
(minimum 25 N/mm2 ) with a minimum pull off strength of 1.5 N/mm2 .
The substrate must be clean, dry and free of all contaminants such as dirt, oil,
grease, coatings and surface treatments, etc.
If in doubt, apply a test area first.
Substrate Preparation
Concrete substrates and cementitious screeds must be prepared mechanically
using abrasive blast cleaning or scarifying equipment to remove cement laitance
and achieve an open textured surface.
Weak concrete must be removed and surface defects such as blowholes and voids
must be fully exposed.
Repairs to the substrate, filling of blowholes/voids and surface levelling must be
carried out using appropriate products from the Sikafloor® , SikaDur® and SikaGard®
range of materials.
High spots must be removed by e.g. grinding.
All dust, loose and friable material must be completely removed from all surfaces
before application of the product, preferably by brush and/or vacuum.
Application
Conditions /
Limitations
Substrate Temperature
+10°C min. / +30°C max.
Ambient Temperature
+10°C min. / +30°C max.
Substrate Moisture
Content
< 3% pbw moisture content.
Test method: Sika® -Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Relative Air Humidity
80% r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the
risk of condensation or blooming on the floor finish.
Application
Instructions
Application Method /
Tools
Roll out the shockpad into the wet Sika® Comfort Adhesive and press down with
Carpet- and Linoleum-Roller (e.g.55 kg) during the tack-phase.
For more detailed informations please refer to the Product Data Sheet of Sika® -
Comfort Adhesive.
Before applying Sikafloor® -Comfort Porefiller allow:
Substrate temperature Minimum Maximum
+10°C 360 min 720 min
+20°C 180 min 360 min
+30°C 90 min 180 min
Waiting Time /
Overcoating
Times are approximate and will be affected by changing ambient conditions
particularly temperature and relative humidity.3
3/3
Sikafloor®-Comfort Regupol 6015H
Notes on Application /
Limitations
Tools
Carpet- and Linoleum-Roller
„SHARK“ – Fixed-Blade PROFESSIONAL Flooring-Knife
Recommended supplier of tools:
TECHNO-Werkzeuge A.E; Vertriebs GmbH
Dieselstr. 44; 42579 Heiligenhaus, Phone: 02056) 9846-0
Info@Techno-Vertrieb.de; Homepage: http://www.techno-vertrieb.de/
PPW-Polyplan-Werkzeuge GmbH, Phone: +49 40/5597260, www.polyplan.com
Under certain conditions, underfloor heating or high ambient temperatures
combined with high point loading, may lead to imprints in the resin.
If heating is required do not use gas, oil, paraffin or other fossil fuel heaters, these
produce large quantities of both CO2 and H2O water vapour, which may adversely
affect the finish. For heating use only electric powered warm air blower systems.
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Local Restrictions Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Health and Safety
Information
For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
Notes:
The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in
good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under
normal conditions in accordance with Sika’s recommendations. In practice, the differences in materials, substrates and actual
site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the product must test the product’s suitability for the intended
application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties
must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the
most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
Sika (China) Ltd.
No.28 Jingdong Road, Suzhou Industrial Park,
JiangSu,P.R.China
Postal Code: 215121
ISO 9001: 2008 ISO 14001:2004
Certificate No.:CC3576 Certificate No.:CC3577
The product is manufactured under a HKQAA
ISO9001/ISO14001
certified quality/environmental management system.
Construction